Picture Framing Equipment Lot: Vacuseal 5298H Dry Mount Press, Morso Chopper, Pistorius Manual Vnailer / Joiner / Underpinner, & Neschen International K 1250 Cold Laminator

UE-031020E-1 Vacuseal 5298H Dry Mount Press $ 3,500

(SOLD)

Includes foam overlay, most of a roll of mounting tissue, and most of a roll of release paper.

From the Seller: "Last used about 6 months ago, this press does need a new heating element in its left third, but everything else functions as it should."

(Note: Heating element is available for purchase from this catalog. Item # NFE-299AI (TS2302097) Heater - Left/Right)

***Manufacturer's Information:

The Seal 5298H Vacuum Dry Mount Press is another leap forward for the Seal/Bienfang company. As the leading company for photo finishing and mounting, Seal has produced a dry mount press that also pre-dries your board, thereby saving time. This press can handle big jobs and handles multiple pieces at the same time.

Bienfang Vacuum Presses are designed to automatically control the four main variables of mounting: moisture, pressure temperature and time. This assures consistent results. There are two simple ways to operate the Vacuum Press: by setting each control individually or by using convenient programmed settings. Some settings are preset at the factory but you can also set your own programs for procedures you conduct repeatedly.

Platen temperature is maintained at +/- 2 degrees F of the set temperature.

Features:

- Built-in stand
- Touch-pad controls
- Easy to read digital display
- Programmable system controller with six preset programs
- End-of-cycle signal
- Space-saving work surface
- Maintenance-free vacuum pump

UE-031020E-2 Morso Chopper

(SOLD)

***Manufacturer's Information:

Morso Model F Mitering Machine

Morso Model F mitring machine cuts double mitre at 45° and single mitre up to 90°. Tenon, mortise joints, and a wide variety of angled cuts can also be made.

When using the Morso F, you will have no dust compared to a saw. Also, the waste of your moulding will be minimized as Morso F cuts double mitres very close, (less than one mm waste of moulding.)

The mitre saw cannot do the mitres as close, and therefore the waste by using a saw, will always be minimum one centimetre.

One centimetre of waste does not sound of much, but if a calculation is done of 100 cuts a day, it actually turns out that the waste over a year is 260 meters waste of moulding! That is only with 100 cuts a day!

Morso F leaves the cut surface of the wood perfectly smooth and accurate, requiring no further preparation before joining. The horizontal movement of the knife block is stepwise adjustable. The sliding longitudinal stop and measuring scale ensure accurate repeat work.

The special lever system of the machine ensures a very easy operation. Twin return springs automatically bring the knives back to starting position.

Morso F is delivered with safety guard, waste chute, sliding longitudinal stop, measuring scale, adjustable fences (45° x 90°), and adjustable rebate supports.

Morso F is manually operated with a foot pedal, needs no compressor or electricity and can therefore be operated anywhere.

Technical data for Morso Model F Mitring Machine
- Double mitre: 45°
- Single mitre: up to 90°
- Cutting width, max.:100 mm
- Cutting height, max.: 160 mm
- Square cutting: 65/65 mm
- Measuring scale up to: 1,500 mm
- Net weight: 90 kg

UE-031020E-3 Pistorius Manual Vnailer / Joiner / Underpinner $ 375

(SOLD)

Pistorius Model VNM

Includes a supply of vnails.

UE-031020E-4 Neschen International K 1250 Cold Laminator $ 600

(SOLD)

Size: 60" x 51" x 35"

Includes about a third of a roll of laminating paper

From the Seller: "It is in good working order. Last used 9 months ago. It can roll on both sides so you can double laminate things too."