Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A
Morso EH Deluxe Chopper (Used) Item # UE-013124A

Used

Morso EH Deluxe Chopper

SKU: UE-013124A
Manufacturer: Morso
Date listed: January 31, 2024

Morso EH Deluxe Chopper

  • Year Manufactured: 2017
  • Model Number: EH
  • Item Under Warranty: No
  • Can Item Be Inspected On-Site: Yes
  • Reason for Selling: "Small framing shop. I use a mitre saw more than this, so it sits quite a bit and is taking up room in the shop. No issues with machine."

From the Seller: "Purchased 2018 at WCAF show... used approximately 2 years, covered and tested 1x per 6 months since. Includes 1 set blades installed in unit and 2 additional sets of blades. Single Phase, 60 HZ, 220 V, 1.1KW, 7.7 Amp, 135 KG wight. No modifications or issues with machine."

Link to Video of Machine in Operation

 

GET PRICING

About this Item

Features & Specifications

***From the Manufacturer:

Morso Model EH mitring machine is a fully automatic electric/hydraulic mitring machine, with a noise level below 70db - the perfect machine to cut picture mouldings in production - wooden, plastic and MDF mouldings.

In principle Morso EH does the same work as the Morso F, but with the Morso EH you have your work done automatically by pushing two push buttons. The Morso EH is safe to operate as you must activate both push buttons at the same time to have the machine work, and therefore you cannot get your fingers underneath the knives. With the Morso EH you can do production all day long. The Morso EH can be delivered either single phase or three phase with voltage to your requirements.

If you compare the Morso EH to a double mitre saw, you will find that first of all the cut with a saw is not as clean and accurate as with the Morso EH. Secondly, there will very often be a problem with the dust from the saw.

On Morso EH there is no dust, as the waste of the moulding is lead straight to the ground, which means it is not necessary to buy and expensive dust extractor.

Another thing is the waste of the moulding. By using a mitre saw, there will always be about one centimetre of waste per cut, but if you use the Morso EH, the waste is minimized to about 1 mm per cut.

A difference to one centimetre may not sound of much, but if the number of cuts are 200 per day, the unnecessary waste of mouldings is 200 cm per day, which is about 520 meters per year..... (Working 5 days a week....).

The Morso EH is supplied with the same standard equipment as the Morso F, plus it has:

- extension table to the left side,
- automatic rebate support and moulding clamps,
- measuring scale 1,500 mm with two adjustable stops - you can cut the short and long length of a frame without having to re-adjust the measurements,
- automatic cutting cycles for both large and small mouldings - which means that the machine always does the trim cut, which is very important
- adjustable length of stroke ( 3 positions ) - when using the lowest cutting position the cutting cycle of two cuts only takes between 1 and 1.5 seconds.

***Concerning "Used" Items: Although we strive for accuracy, some specifications are provided to us by the Seller. Cross-check with manufacturer for any difference between the machine being sold and what is stated in the manufacturer's information. Descriptions of condition of the equipment are not warranties. Descriptions are intended only as a courtesy and their accuracy is not guaranteed. Buyer inspection encouraged. There are no warranties or guarantees implied unless otherwise stated. All items are sold "As Is, Where Is, and With All Faults." No guarantee is made as to fitness for a particular purpose, implied or otherwise. Feel free to contact us if you have further questions before purchasing.

Pricing & Shipping

Shipping Notice: Unless specified on the product, items are FOB Origin. It is the responsibility of a customer to pickup, either personally or by a contracted shipping agent, their product.

Interested in the product? Fill out the form or call us at 330-405-9421 for pricing and other information.

Product is located in Illinois. Customers can pick the machine up or have it shipped for an additional fee.

Get Pricing

Interested in the product? Fill out the form or call us at 330-405-9421 for pricing and other information.

Product is located in Illinois. Customers can pick the machine up or have it shipped for an additional fee.

  • Do not include +1 country code. If outside of USA, please include phone number in message box.

Can't Find the Equipment You Need?

We're constantly getting new listings. Let us know what you're looking for and we'll notify you when the equipment is available.