Catalog

Woodworking Equipment Lot: Hoffmann MU-2P Router Machine, Hoffmann Notching Machine, & Supplies (used) Item # UE-120121A (Connecticut)

SKU: UE-120121A

Woodworking Equipment Lot: Hoffmann MU-2P Router Machine, Hoffmann Notching Machine, & Supplies

Click Here to Contact Us for Pricing

Available Items in Lot:

    • SKU # UE-120121A-2 Hoffmann Morso Notching / Cutting Machine
    • SKU # UE-120121A-3 Delta Radial Arm Saw
    • SKU # UE-120121A-4 Martin Shaper w/ Steff Feeder
    • SKU # UE-120121A-5 Morso SKM Extra Pieces

Sold Items in Lot:

    • SKU # UE-120121A-1 Hoffmann MU-2P Manual Router

From the seller: “All equipment in this lot are in good working condition unless otherwise specified below.”

Machines can be purchased as a lot or individually.  See below for individual item pricing.


UE-120121A-1 Hoffmann MU-2P Pneumatic Router (Sold)

*** From the manufacturer:

Hoffmann MU-2P Pneumatic Routing Machine

From the Manufacturer:

The Hoffmann MU2-P bench-top routing machine is equipped
with a high speed router motor, located at the center of the machine. The
supplied 45 degree fence plate, which is guided in a keyway in the machine
table, is used to accurately position the material on the table. The location of
the dovetail slot for the Hoffmann Dovetail Key is adjusted by simply moving
this fence plate. Once set, the plate is locked in place and the routing
sequence can begin. The machine is equipped with a pneumatic pedal that starts the routing
process. Upon depressing the foot pedal, the routing sequence is initiated:

*pneumatic clamp secures workpiece on machine table
*router head advances until the pre-set height position is reached
*router head returns to base position
*pneumatic clamp releases work piece

Output is approx. 16 routing strokes per minute, which translates into 2 completely processed rectangular frames. These numbers include material handling, but obviously depend on routing depth, feed speed, material flow and operator performance as well. Flow control valves on the main pneumatic cylinder allow the operator to adjust the upward and downward feed rate independently, depending on the material being processed. On its backside, the large heavy-duty cast aluminum machine base has a 1 3/4″ diameter dust collection port to connect a shop vacuum for dust free operation.The supplied outer bit is solid tungsten carbide, made to exacting specifications. Depending on the routing depth and the material to be routed, the useable cutter life is approx. 10,000 strokes. Every machine is shipped with a tool kit and set-up jig, which allows a router, bit change in only minutes. Diamond tooling is also available.

Features

* Air regulator

* Air filter

* Oil lubricator assembly

* W-2 carbide router bit

* Standard 45 degree fence plate and square top installed


UE-120121A-2 Hoffmann Morso Notching / Cutting Machine

*** From the manufacturer

The MORSO NM notching machine is manually operated, light-duty notching machine for the production of beaded face-frames, French-mitered cabinet doors as well as muntin and mullion joints.
While this is smallest MORSO notching machine available, the manual operation of the machine, the shape of the cutting head and the MORSO length stop fences are based on the larger NFL and NFXL models.

The main differences between the MORSO NM notching machine and the larger, heavy-duty MORSO NFL and MORSO NFXL notching machines are a smaller base frame and reduced footprint, lower table height, sheet-metal extension tables in place of cast-iron tables, overall lighter construction and smaller cutting head and knives. The center table is borrowed from a MORSO guillotine-style moulding chopper and the center stop is a flip-stop design.The vertical travel of the cutting head (and thus the resting position of the foot pedal) can be adjusted depending on workpiece thickness, assuring comfortable operation.

Optional smaller Cutting Head
To increase the range of applications, we offer smaller cutting heads for MORSO NM notching machines. These smaller heads are required to install 1/4”, 5/16” or 3/8” wide nose knives which are generally used for mullion or muntin joinery. The cutting heads can be replaced in only minutes and MORSO NM side knives fit on both heads; only the nose knives differ in design.

Operation:
Beaded Face-Frame Notching Operation – full notch in stiles to accept cross rails (shown on MORSO NM)
Upon adjusting the cock-bead stops to set the notching depth, the moulding is placed on the machine table and one end is rested against a flip-stop. The hand lever in front is used to move the cutting head horizontally to and from the operator. Depending on the width of the cut, the thickness and hardness of the moulding, two to four cuts are made to complete the notch. This process takes only seconds and the resulting cuts are smooth and free of tear-out.

Beaded Face-Frame Notching Operation – half notch in stiles to accept top and bottom rails (shown on MORSO NFL)
A half-notch for top and bottom rails is cut into the left and right stiles in the same manner as a full notch. A “long arm” flip-stop is used to position the stile properly (the long arm is designed to reach past the cock-bead stops). For wider cross rails the stile is moved sideways after each cut until the desired notch width is reached.

Beaded Face-Frame Coping Operation – clipped corners on rails (shown on MORSO NM)
Upon adjusting the setscrews in the nylon center fitting, the stop is moved toward the cutting head and locked in place. The rail is placed on the table and pushed against the stop. The 45-degree corner cut on the bead is made in one cycle, multiple cuts are not necessary. The moulding is then flipped end-for-end and the process is repeated.

Window Mullion Notching Operation – step 1 (shown on MORSO NFL)
Upon adjusting the cock-bead stops to set the notching depth, the moulding is placed on the machine table and one end is rested against a flip-stop. The hand lever in front is used to move the cutting head horizontally to and from the operator. Two cuts are generally enough to produce a clean notch.
IMPORTANT:
The mullion profile must have a “flat-spot” in the center and this flat spot should match the width of the nose knife. We highly recommend you produce your mullions with a 1/4” flat spot – you can then use not only a 1/4” wide nose knife with your notching machine but also a 1/4” spiral router bit on a Hoffmann routing machine for step 3.

Window Mullion Notching Operation – step 2 (shown on MORSO NFL)
Once all notches are cut along one edge of the mullion, the process is repeated on the other side. It is important to have the notches aligned for tight joints.
A DGS 1000 fence system is a worthwhile investment for these operations.

Window Mullion Routing Operation – step 3 (shown on Hoffmann X-20)
Once all notches are cut on a MORSO notching machine, one-half of the mullion stock needs to be removed to create a half-lap joint. We offer a complete fixture set including the necessary 1/4” spiral down-cut bit under part number W30110000 Half-Lap Joint Fixture Kit.
One set of mullions (either the vertical or the horizontal pieces) are routed from the bottom up and the other set must be routed from the face side down.
We use a spiral down-cut bit to minimize “fuzzing” or tearing of the material, a slow and steady routing stroke produces very clean cuts even on profiled mullions.
Fixtures are compatible with Hoffmann X-20, MU3, MU3-D, MU3-P and MU3-PD machines.

Mullion on half-lap fixtures – cutting into top (front) of mullion

Mullion on half-lap fixtures – cutting into bottom (back) of mullion

Completed half-lap mullion joint – front

Completed half-lap mullion joint – back

Options:
Optional DGS 1000 GlideStop Fence system for MORSO NM
A complete GlideStop fence system is available as an option for all MORSO notching machines.
This upgrade offers the following benefits:
Fully adjustable index stops can be set at any point along the fence rails for repeated accuracy
Index Stops can be spaced as close as 9/16″ apart
Twenty index stops are included in the basic package, additional Stops can be added anytime
Index stops can be by-passed at any time without moving and re-setting
Self-adhesive tape scales on both fence rails for accurate positioning in 1/32″ increments
Offers the benefits of twenty standard flip-stops at a fraction of the cost

Once set, the GlideStop uses a spring-loaded contact arm to register against the index bolts. This “mechanical memory” design has the accuracy needed to make precisely spaced face-frames, again and again. It is especially helpful for repetitive settings like drawer banks, door openings, etc. which do not change from job to job. In addition, the system allows the user to by-pass pre-set index bolts at any time, without having to move and re-adjust the stops!
The contact arm is simply tilted forward, sliding over the stop index.

The location of the GlideStop is shown on the tape scale, hairline pointers on each side make set-up fast and reliable. An optional digital upgrade is available if a digital read-out in inches and millimeters is preferred.
The patented GlideStop design uses a pressure bar to clamp against the fence rail. This avoids the marring of the rails by the locking lever, and it also assures positive clamping without “creeping”. Simply slide the GlideStop to the desired position and turn the locking lever – done.

MORSO NM Standard Features:

MORSO NM foot operated notching machine for beaded face-frames include:
safety guard
two flip-stops
one center flip-stop
left and right hand side sheet metal table extensions
left and right hand side aluminum fence rails
one set of original MORSO side knives for NM, factory ground and honed
one 3/4″ wide nose knife for NM, factory ground and honed
detailed instructions incl. parts diagrams, toolkit

Warranty:
Mechanical parts are warranted for twelve months.
Complete MORSO warranty terms apply.

UE-120121A-3 Delta Radial Arm Saw


UE-120121A-4 Martin Shaper w/ Steff Feeder


UE-120121A-5 Morso SKM Extra Pieces


This machine can be picked up in Connecticut or have it shipped for additional fee.

*** Although we strive for accuracy, some specifications are provided to us by seller. It is a good idea to double check specifications by manufacturing company for possible errors of information. Check with manufacturer for any difference between the machine being sold and what is stated in the manufacturer’s website.  Feel free to call us if you have further questions before purchasing.

Catalog Item #

UE-120121A

Condition of Item

Used
All used items are sold “As Is”. There are no implied warranties or guarantees. Statement of condition is provided to us by the seller. Although we strive to obtain the best information from the seller, AIM is not responsible for inaccuracies provided to us by seller. It is the responsibility of the buyer to inspect machinery; crosscheck with seller or manufacturer regarding descriptions and specifications that appear in this listing.

Date of Initial Listing

December 1, 2021

Location

Connecticut

Reviews

There are no reviews yet.

Be the first to review “Woodworking Equipment Lot: Hoffmann MU-2P Router Machine, Hoffmann Notching Machine, & Supplies (used) Item # UE-120121A (Connecticut)”

Your email address will not be published.

Related Products